Exterior shutters installation

Establish also that screws placed in the four corners of the exterior panel will connect with a solid surface. The bottom rail is larger than the top and the louvers will angle up and away from the building. Center the holes on the side stiles, aligned with the top of the bottom rail and bottom of the top rail.

Countersink the holes on the face of the shutter if the holes will be filled before painting. Step 3: Return the shutter to the side of the window. Insert an exterior grade screw, or bolt, in the top hole on the window side. The selected fastener should be corrosion resistant to ensure the longest possible life to permanently secure the panels in a fixed open position.

Nails are not recommended because they can become loose over time, and there is a risk of damaging the face of the house shutter when pounding with a hammer. Hot dipped galvanized steel bolts are a very substantial option, but are often more bulky than necessary to install exterior shutters. The bolt head will likely sit proud of the face resulting in an unsightly appearance. High-quality exterior grade stainless steel or deck screws with a lifetime polymer coating for wood siding are recommended.

Some screw heads are designed to self counter sink. Brick surfaces require specialty anchors and masonry screws. Do not tighten the screw past the panel face. Outdoor panels installed permanently against the building may trap water, which can be damaging to the house and the window shutters. A narrow gap is sufficient to allow air to pass between the two surfaces, allowing moisture to escape and evaporate. Rubber washers or another non-corrosive spacer can be used to ensure adequate ventilation.

Step 5: Use a level on the side of the panel to ensure the final location is plumb. Step 6: Fasten the bottom window side screw, followed by the final two corners. Excessively wide or tall shutters may benefit by the addition of screws in the vertical center of the stiles.

Step 7: Fill the void of a countersunk hole with an exterior putty, let dry, sand, then paint. Step 8: Repeat the process for the opposite side shutter to successfully complete the installation.

Additional provisions may be necessary. Every window on every house is unique, which results in a unique approach and application for each situation.

Wood tropical Bahama shutters are installed with a top mounted hinge. Separate instructions are provided to install Bahama shutters. Shop Now. How to Install Wood Exterior Shutters The procedure to install wood exterior shutters is largely determined by the window configuration and function they will be asked to perform. Exterior Shutter Hinge Guide. Where to Buy Exterior Shutter Hinges.

See How to Install Bahama Shutters. Outdoor Shutter Dog Guide. Where to Buy Exterior Shutter Dogs. Committed to help you select the best exterior shutters for your house. This method uses two interlocking lengths of wood or metal. One piece attaches to the building and the other to the back of the shutter. The down-facing shutter side crosspiece is lowered onto the upward slanted bottom bracket.

Similar z-bar, or z-clips, hold the shutter against the building. Locking cleats will ensure the shutters do not slide or fall out. Composite shutters may also be installed direct to the building with screws. The screws enter through the face of the shutter and extend into the building.

Each panel must be secured at all four corners. It may be necessary to add screws in the center edges for taller shutters. Fasteners should be corrosion resistant to ensure the longest possible life to permanently secure the panels in a stationary open position.

Nails are not recommended because they can become loose over time, and hammering may damage the window shutters. Hot dipped galvanized steel bolts are a very substantial option, but are often more bulky than necessary to install exterior shutters. High-quality exterior grade stainless steel or deck screws with a lifetime polymer coating for wood siding are advised. The screw length needs to be sufficient to pass through the 1. This method is best used for wood siding, but can be used with other stable materials.

Hard surfaces will need to employ a wall anchor. Composite panels can be installed with shutter specific outdoor hinges. There are several reasons homeowners choose this particular method. First, exterior hardware enhances character. The additional detail contributes to a complete presentation with depth and form. Outdoor shutter hinges support the panels on the window side.

When closed, the central barrel of the hinge is visible. Shutter dogs hold the shutters in a locked open position. Shutter dogs are often constructed into intricate shapes. Hardware also enables the shutters to swing open and closed. One portion of the hinge attaches to the building, with a second segment to the shutter. Composite shutters do need to be pre-drilled before screws can be used.

The hinge then pivots, allowing the shutters to rotate horizontally. Exterior composite shutters do only have one presentable side. The back is flat with no detail, so composite shutters can be closed occasionally for storm protection.